Using Calorimetry (Edexcel International AS Chemistry)

• Calorimetry is the measurement enthalpy changes in chemical reactions
• There are two types of calorimetry experiments you need to know:
  • Enthalpy changes of reactions in solution, e.g. displacement and neutralisation
  • Enthalpy changes of combustion

• In both cases, you should be able to give an outline of the experiment and be able to process experimental data using calculations or graphical methods

Enthalpy changes for reactions in solution

• The principle of these calorimetry experiments is to carry out the reaction with an excess of one reagent and measure the temperature change over the course of a few minutes
• The apparatus needed to carry out an enthalpy of reaction in solution calorimetry experiment is shown below
  • A calorimeter can be made up of a polystyrene drinking cup, a vacuum flask or metal can

Sample method for a displacement reaction

1. Using a measuring cylinder place 25 cm³ of the 1.0 mol dm^-3 copper(II) sulphate solution into the polystyrene cup
2. Weigh about 6 g of zinc powder - as this is an excess there is no need to be very accurate
3. Draw a table to record the initial temperature and then the temperature and time every half minute up to 9.5 minutes
4. Put a thermometer or temperature probe in the cup, stir, and record the temperature every half minute for 2.5 minutes
5. At precisely 3 minutes, add the zinc powder to the cup (DO NOT RECORD THE TEMPERATURE AT 3 MINUTES)
6. Continue stirring and record the temperature for an additional 6 minutes

• For the purposes of the calculations, some assumptions are made about the experiment:
  • That the specific heat capacity of the solution is the same as pure water, i.e. 4.18 J g^-1 K^-1
  • That the density of the solution is the same as pure water, i.e. 1 g cm^-3
  • The specific heat capacity of the container is ignored
  • The reaction is complete
  • There are negligible heat losses

Temperature correction graphs

• For reactions which are not instantaneous there may be a delay before the maximum temperature is reached
• During that delay the substances themselves may be losing heat to the surroundings, so that the true maximum temperature is never actually reached
• To overcome this problem we can use graphical analysis to determine the maximum enthalpy change

A temperature correction graph for a metal displacement reaction between zinc and copper sulfate solution. The zinc is added after 4 minutes

The steps to make a temperature correction graph are:

1. Take a temperature reading before adding the reactants for a few minutes to get a steady value
2. Add the second reactant and continue recording the temperature and time
3. Plot the graph and extrapolate the cooling part of the graph until you intersect the time at which the second reactant was added

Analysis

• Use both extrapolated lines to calculate ΔT as shown on the graph
• Use the equation q  = mcΔT to calculate the energy transferred
  • q = energy transferred
  • m = mass - this will be the mass of the 25 cm³ solution which will be 25 g (assuming a density of 1 g cm^-3)
  • c = specific heat capacity - this will be assumed to be 4.18 J g^-1 K^-1, which is the specific heat capacity of water
  • ΔT = the temperature change from the graph
• Convert your value for energy transferred from J into kJ
• Then use the equation ΔH =  to calculate the enthalpy change for the reaction
  • q = energy transferred
  • n = number of moles - this would be the number of moles of the limiting reagent, which means that you will have an extra calculation to do to determine whether this is the zinc or the copper sulfate 
• Remember that in the example above, the temperature of the reaction mixture increased which means that the reaction is exothermic and should, therefore, have a negative value

   Answer

• • q = m x c x ΔT
    • m (of resulting solution) = 25.0 + 50.0 = 75.0 g
    • c (of water) = 4.18 J g^{-1 o}C^-1
    • ΔT (of water) = 6.5 ^oC
  • q = 75.0 x 4.18 x 6.5 = 2038 J

Enthalpy of combustion

• The principle here is to use the heat released by a combustion reaction to increase the heat content of water
• A typical simple calorimeter is used to measure the temperature changes to the water

A simple combustion calorimeter

• To complete this experiment, the following steps will need to be completed:

• It is important that you record the starting temperature, and the final temperature in order to complete the calculations
• You must also record the starting mass of the spirit burner and the final mass of the spirit burner, so that you can work out the mass of the fuel burned during the reaction
  • This will then be used to calculate the moles, which will be used to convert Q to an enthalpy change in your calculations

Key points to consider

• Not all the heat produced by the combustion reaction is transferred to the water
  • Some heat is lost to the surroundings
  • Some heat is absorbed by the calorimeter

• To minimise the heat losses the copper calorimeter should not be placed too far above the flame and a lid placed over the calorimeter
• Shielding can be used to reduce draughts
• In this experiment the main sources of error are
  • Heat losses
  • Incomplete combustion

   Answer

   Step 1:

• • q = m x c x ΔT
  • m (of water) = 500 g
  • c (of water) = 4.18 J g^{-1 o}C^-1
  • ΔT (of water) = 68 ^oC - 25 ^oC = 43 ^oC

   Step 2: 

• • q = 500 x 4.18 x 43 = 89 870 J

   Step 3: 

• • This is only 30% of the total energy released by methane
  • Total energy x 0.3 = 89 870 J
  • Total energy = 299 567 J

   Step 4:  

• • This is released by 2.50 g of methane
  • Energy released by 1.00 g of methane = 299 567 ÷ 2.50 = 120 000 J g^-1 (to 3 s.f.) or 120 kJ g^-1

• Aqueous solutions of acid, alkalis and salts are assumed to be largely water so you can just use the m and c values of water when calculating the energy transferred.
• To calculate any changes in enthalpy per mole of a reactant or product the following relationship can be used:

ΔH = 

• When there is a rise in temperature, the value for ΔH becomes negative suggesting that the reaction is exothermic
  • This means that your value should be negative for an exothermic reaction, e.g. combustion
• When the temperature falls, the value for ΔH becomes positive suggesting that the reaction is endothermic
  • This means that your value should be positive for an endothermic reaction, e.g. ammonium salts dissolving in water

Answer

Step 1: Calculate the energy released by the organic liquid

• • Q = mcΔT
  • Q = 100 x 4.18 x (75 - 20)
  • Q = 22990 J
  • Q = 22.99 kJ

Step 2: Calculate the number of moles of the organic liquid

• • Number of moles = 0.0259 moles (to 3s.f.)

Step 3: Calculate the enthalpy change of combustion

• • Δ_cH^θ -887 kJ mol^-1 (to 3s.f.)
    • Remember, combustion is an exothermic process and will, therefore, be a negative enthalpy change value