Practical Skills I : Planning (Edexcel International A Level Physics)

Exam Questions

38 mins4 questions
1a
Sme Calculator
1 mark

A student planned an experiment to determine the density of acetate.

She was given a pack of 50 acetate sheets and had access to standard laboratory apparatus.

q1-wph13-03-june-2021-edexcel-int-as-a-level-phy

The approximate dimensions of a single sheet of acetate are given on the pack.

Length 30 cm
Width 21 cm
Thickness 0.15 mm

 

The total mass of 50 acetate sheets is approximately 670 g.

To determine the density of acetate, the student needed to take measurements.

Complete the table below.

Quantity to be measured Measuring instrument Resolution
Mass  Balance 0.1 g
Length and width Metre rule  
Thickness Vernier calipers  

  

1b
Sme Calculator
4 marks

Describe a method to determine an accurate value for the density of acetate.

1c
Sme Calculator
2 marks

The student then followed the same method using thicker sheets of acetate.

Explain why using thicker sheets of acetate would reduce the uncertainty in her value for density.

Did this page help you?

2a
Sme Calculator
2 marks

A student investigated the acceleration of a trolley as it rolled down a ramp. The trolley was released from rest at the top of the ramp and allowed to roll onto a horizontal surface. There was a single light gate above the horizontal surface, as shown.

q1-wph13-03-jan-2022-edexcel-int-as-a-level-phy

The light gate was connected to a data logger. The data logger recorded the time taken for the card to pass through the light gate.

Describe how the student could determine the velocity v of the trolley as it passed through the light gate.

2b
Sme Calculator
6 marks
The student repeated the procedure and determined four values of v. The values are shown in the table.

v / m s–1
2.07 1.84 1.91 2.10

 

i)
Calculate the mean value for v and the percentage uncertainty in v.

(3)





Mean v = ............................ m s–1
Percentage uncertainty in v =........................... %

ii)
The student measured the distance s that the trolley travelled on the ramp.

Determine the acceleration of the trolley on the ramp.

s = 1.50 m

(2)




Acceleration = ............................. m s–2

iii)
A second student carried out the same experiment and determined a similar value for the acceleration of the trolley on the ramp.

State why this does not show that the results are reproducible.

(1)

Did this page help you?

3a
Sme Calculator
4 marks

A student was asked to investigate the ultimate tensile stress of a sample of thin nylon fishing line.

Describe a method to determine the maximum force the nylon fishing line can withstand before breaking.

3b
Sme Calculator
2 marks
Identify one safety issue with this investigation and how it may be dealt with.
3c
Sme Calculator
8 marks

Before testing, the student measured the diameter at five points along the sample of nylon fishing line.

            0.55mm        0.57mm       0.54mm      0.55mm       0.53mm

i)
Calculate the percentage uncertainty in the mean diameter of the nylon fishing line.

(3)



Percentage uncertainty = .........................................

ii)
The student read an article that suggested nylon fishing line can absorb water.

The article suggested that the ultimate tensile stress of nylon decreases by 10% after absorbing water.

She repeated her experiment, using new samples of fishing line before and after they absorbed water.

Sample Maximum force / N Diameter / mm
Before 65.8 0.45
After 57.8 0.46

Evaluate whether her results support the suggestion in the article.

(5)

Did this page help you?

4a
Sme Calculator
6 marks

The specific latent heat of vaporisation L of water can be determined using the apparatus shown.

q2-wph16-06-june-2021-edexcel-int-as-a-level-phy

Devise a plan to determine the value of L using a graphical method.
You should include a circuit diagram and any additional apparatus required.


4b
Sme Calculator
3 marks

One significant source of error in this experiment is the uncertainty in the mass reading due to the water moving as it boils.
Explain how another significant source of error affects the value of L.


Did this page help you?