Revision NotesExam QuestionsPast Papers
ASPhysicsOCRExam Questions4. Electrons, Waves & Photons4.2 Resistance & Resistivity

Resistance & Resistivity (OCR AS Physics)

Exam Questions

45 mins14 questions

Select a question set to download for
4.2 Resistance & Resistivity

Select an answer set to view for
4.2 Resistance & Resistivity

Medium
Hard
1
Sme Calculator1 mark

A circuit with four light-emitting diodes (LEDs) P, Q, R and S is shown below.

q5-paper-2-nov-2021-ocr-a-level-physics

Two LEDs are lit in this circuit. Which two LEDs are lit?

  • P and Q

  • P and R

  • Q and R

  • Q and S

Choose your answer

Did this page help you?

2
Sme Calculator1 mark

A circuit is shown below.

q4-paper-2-june-2017-ocr-a-level-physics

The battery has negligible internal resistance. The temperature of the NTC thermistor is decreased.

Which of the following statements is/are correct?

1    The current at X increases.
2    The current at Y remains the same.
3    The potential difference across the thermistor increases.

  • 1, 2 and 3

  • Only 2 and 3

  • Only 3

  • Only 2

Choose your answer

Did this page help you?

3
Sme Calculator1 mark

Determine the current flowing through a 5 Ω resistor when a 6 V voltage supply is applied across it.

  • 11.0 A

  • 0.83 A

  • 4 A

  • 1.2 A

Choose your answer

Did this page help you?

4
Sme Calculator1 mark

Below is the current-voltage curve for a NTC thermistor.

4-2-mcq-m-q2-ocr-al-physics

Which of the following statements is/are correct?

  1. The higher the current passing through a NTC thermistor, the higher the resistance.
  2. As the potential difference across a NTC thermistor increases, its resistance decreases.
  3. NTC thermistors obey Ohm’s law.

  • 1, 2 and 3

  • Only 2

  • 2, 3

  • 1 and 3

Choose your answer

Did this page help you?

5
Sme Calculator1 mark

A metal wire with circular cross-section has a length of 2.0 m and a diameter of 5.0 mm. The wire’s resistance is determined experimentally and found to have a value of 4.0 Ω. Calculate the resistivity of the metal making up the wire.

  • 6.0  × 10-5 Ω m

  • 4.0  × 10-5 Ω m

  • 2.0  × 10-5 Ω m

  • 1.6  × 10-4 Ω m

Choose your answer

Did this page help you?

6
Sme Calculator1 mark

A student is tasked with determining the resistivity ? of a wire represented by the resistor in the following diagram. The student measures the diameter of the wire using a vernier caliper and its length using a ruler. The student now needs to calculate the resistance of the wire before combining these results with his measurements of the length and diameter of the wire to calculate the resistivity.

The diagram below shows the circuit used by the student to perform the experiment:

4-2-mcq-m-q5-ocr-al-physics

Which electronic components, that are needed to determine the resistance of the wire, are missing from the diagram?

  • Only an ammeter placed in series with the wire.

  • A voltmeter placed in series and an ammeter placed in parallel with the wire.

  • A voltmeter placed in parallel and an ammeter placed in series with the wire

  • Only a voltmeter placed in series with the wire.

Choose your answer

Did this page help you?

1
Sme Calculator1 mark

The diagram below shows the graph of current against voltage for a filament lamp.

4-2-mcq-h-q1-ocr-al-physics

Which of the following statements about the results in the graph is/are incorrect?

  1. The resistance of the lamp at Y is higher than the resistance at Z.

  2. The power dissipated by the lamp at X is less than the power dissipated at Y.

  3. The current increases with voltage at a decreasing rate.

  • Only 1

  • Only 2

  • 1 and 2

  • 1, 2 and 3

Choose your answer

Did this page help you?

2
Sme Calculator1 mark

A student wishes to cut an aluminium wire of uniform diameter to the same weight and resistance as a copper wire of length 50 cm.

Aluminium has a resistivity that is 1.5 times greater than that of copper, and is about 3 times less dense than copper. 

How long should the aluminium wire be to satisfy the experimenter's requirements?

  • 33 cm

  • 68 cm

  • 71 cm

  • 135 m

Choose your answer

Did this page help you?

3
Sme Calculator1 mark

A circular hoop is made of metal wire with resistivity ρ, diameter D, and thickness d. The hoop is connected to a circuit at points A and B, as shown in the diagram below.

Two points on the hoop separated by a quarter of the hoop’s circumference are pinched and soldered together at point P to create a shape consisting of two squashed hoops with points A and P.

 4-2-mcq-h-q3-ocr-al-physics

Terminals A and B of a battery with an e.m.f ε and internal resistance r are positioned to ensure pairs of equal-length paths from A to P and from B to P.

What is the total current passing through the circuit?

  • I space equals space fraction numerator epsilon d squared over denominator d squared r space minus space 4 rho D end fraction

  • I space equals space fraction numerator 4 epsilon d squared over denominator rho D end fraction

  • I space equals space fraction numerator epsilon over denominator r space plus space fraction numerator 5 rho D over denominator 4 d squared end fraction end fraction

  • I space equals space fraction numerator epsilon over denominator r space plus space fraction numerator rho D over denominator d squared end fraction end fraction

Choose your answer

Did this page help you?

4
Sme Calculator1 mark

An NTC thermistor is connected to a variable voltage source. 

Which of the following statements about the thermistor is/are correct:

  1. As the voltage across the thermistor gradually increases, its resistance decreases linearly

  2. As the temperature of the thermistor decreases, the current passing through the thermistor increases exponentially

  3. The gradient of the current-voltage curve for an NTC thermistor increases with voltage

  • Only 1

  • Only 3

  • 1 and 3

  • 1, 2 and 3

Choose your answer

Did this page help you?

5
Sme Calculator1 mark

A wire with uniform circular cross-section is stretched until its radius is reduced by half. The volume of the wire remains uniform throughout the stretching process.

Once the wire has been stretched, it is cut into three equal lengths and the pieces are connected in parallel with each other.

What is the ratio of the resistance of the original wire to the new resistance of the parallel combination?

  • 23{"language":"en","fontFamily":"Times New Roman","fontSize":"18","autoformat":true}

  • 34{"language":"en","fontFamily":"Times New Roman","fontSize":"18","autoformat":true}

  • 12{"language":"en","fontFamily":"Times New Roman","fontSize":"18","autoformat":true}

  • 916{"language":"en","fontFamily":"Times New Roman","fontSize":"18","autoformat":true}

Choose your answer

Did this page help you?